Skip to content
Custom battery lines. Training before shipment.Request a Quote

Knowledge

We Analyzed 31 Published Electrode Measurements. The Lowest-Resistance Blend Lost at 5C.

A secondary analysis of 31 published LFP electrode measurements compares carbon black, CNT and graphene across resistivity, rate performance and calendering rebound.

Fine black conductive carbon black powder in a ceramic dish

“Lower electrode resistance is better.”

It is the default rule most cathode formulation teams inherit from lithium iron phosphate (LFP). Add a conductive agent, watch the resistivity drop, ship the formulation.

But NFPP — Na₄Fe₃(PO₄)₂P₂O₇, the polyanion cathode most sodium-ion projects are now scaling — does not give you the carbon budget to play that game. Its intrinsic conductivity is lower, its compaction is lower, and its energy density headroom is roughly 60% of LFP’s. Every 0.1% of inactive additive costs more.

We wanted to test that rule against published data. To do this, we re-analyzed 31 published measurements from LFP electrode experiments — 12 resistivity values, 15 impedance/rate/cycling values and 4 calendering-rebound values — alongside four published NFPP case studies.

The rule broke immediately. At an identical 1.5 wt% total additive loading, the blend with the lowest ohmic resistance (28.2 mΩ) delivered the worst 5C capacity retention (87.6%). The blend with the third-lowest resistance (33.7 mΩ) delivered both the best rate performance (93.5%) and the best 500-cycle retention (95.8%).

Below, we break down the numbers, explain why the electron path and the ion path pull in opposite directions, and give pilot-line teams a validation sequence that survives scale-up.

Important scope note: this is a secondary analysis of published experimental data, not a new lab experiment. We built no cells and measured no electrodes. All LFP figures below are LFP figures; all NFPP figures are labelled as such.


Key takeaways


Methodology

We re-analyzed a compiled set of published LFP and NFPP electrode measurements. We re-checked every number, re-plotted the datasets and separated LFP evidence from NFPP evidence. This is a secondary analysis of published data, not an experiment we ran.

Dataset What it contains Count System
A Electrode volume resistivity, 3 additives × 4 loadings (1, 2, 3, 6 wt%) 12 values LFP
B Four blends at fixed 1.5 wt% total loading: ohmic R, charge-transfer R, 5C retention, 500-cycle retention 15 values (one not reported) LFP
C Thickness rebound after drying, same four blends 4 values LFP
D Four NFPP graphene/CNT case studies with rate and cycle results 4 studies NFPP

Total for A+B+C: 31 measured values. Dataset D is separate case-study evidence and is not pooled with A–C.

Units are as reported: Ω·cm for volume resistivity, mΩ for impedance, % for capacity retention and thickness rebound. We drew no new trendlines through unreported points, added no interpolated values and computed no statistics beyond ratios between reported values.

Three limits matter before you read the charts:

  1. A, B and C are LFP measurements. They tell us about the relative ranking and the mechanism, not about absolute NFPP values. NFPP absolute values must be measured on your own material batch.
  2. The source does not provide error bars, raw datasets, sample sizes or DOIs, so we cannot compute uncertainty or significance, and we do not claim any.
  3. Values come from different published studies and are not pooled into a single model. Where we say “best” or “worst”, we mean within the four-blend, same-loading comparison in Dataset B.

This is a test of an engineering rule of thumb against published measurements — not a claim that any additive causes a given rate or cycle result.


At 1% loading, the three additives are ~39x apart in resistivity

At 1% loading, the three additives are ~39x apart in resistivity LFP electrode volume resistivity (ohm.cm), log scale. Lower is better. FIG 1 100 10 1 0.1 1% 2% 3% 6% Conductive additive loading (category axis) 82.4 51.7 29.8 8.3 20.5 11.6 2.1 0.9 2.1 0.8 0.4 0.16 Carbon black CNT Graphene 82.4 vs 2.1 ohm.cm at 1% = a ~39x spread at equal loading Source: published LFP electrode measurements, secondary re-plot. NOT NFPP measurements. Values: 12 measurements across 3 additives x 4 loadings.

Fig 1. LFP electrode volume resistivity vs conductive-additive loading, log scale. Source: published LFP measurements, secondary re-plot. Not NFPP measurements. 12 values across 3 additives × 4 loadings.

The published LFP series is unambiguous:

Loading Graphene CNT Carbon black
1% 2.1 Ω·cm 20.5 Ω·cm 82.4 Ω·cm
2% 0.8 11.6 51.7
3% 0.4 2.1 29.8
6% 0.16 0.9 8.3

All three curves fall, but they start nearly 40x apart and fall at different rates. Graphene enters the 1 Ω·cm range at 2%. CNT needs 6% to get there — at 3% it is still at 2.1 Ω·cm. Carbon black is still at 8.3 Ω·cm at 6%, an order of magnitude above graphene.

Why NFPP cannot simply “add more carbon black.” The published review puts NFPP compaction at 2.1–2.3 g/cm³ (front-runners ~2.5) against LFP’s 2.6–2.8 g/cm³, theoretical capacity at 129 mAh/g against 170 mAh/g, and average voltage at 3.1 V against 3.4 V. Multiplying the ratios gives ~0.63, which matches the industry shorthand that NFPP cell energy density is about 60% of LFP’s.

The base is already low. At 3% loading — a realistic upper bound — the gap between carbon black (29.8 Ω·cm) and CNT (2.1 Ω·cm) is 14x, and carbon black would need far more than 3% to close it. NFPP does not have that share to give.

What this means for formulation teams

High-efficiency conductive agents are not a premium option for polyanion cathodes; they are a consequence of the carbon budget. Set the total from your target compaction and energy density first, then decide how to divide it — not the other way around.


The lowest-resistance blend had the worst 5C retention

The lowest-resistance blend had the worst 5C retention Four blends at an identical 1.5 wt% total additive loading (LFP data). FIG 2 0 10 20 30 40 Ohmic R (mOhm) 84% 87% 90% 93% 96% 5C retention 39.9 1.5% CB 33.7 0.5% CB + 1.0% CNT 32.0 1.5% CNT 28.2 0.5% CB + 1.0% Gr 89.3% 93.5% 91.8% 87.6% LOWEST ohmic R = 28.2 mOhm / WORST 5C = 87.6% -> electron and ion paths diverge Source: published LFP electrode measurements, secondary re-plot. NOT NFPP measurements. 500-cycle retention: 92.4% / 95.8% / 90.1% / not reported (same order).

Fig 2. Four blends at an identical 1.5 wt% total additive loading. Bars: ohmic impedance (left axis). Dashed line: 5C capacity retention (right axis). Source: published LFP measurements, re-plotted. Not NFPP measurements. 500-cycle retention, in the same order: 92.4% / 95.8% / 90.1% / not reported.

Here is Dataset B in full:

Blend (1.5 wt% total) Ohmic R Charge-transfer R 5C retention 500-cycle retention
1.5% carbon black 39.9 mΩ 8.2 mΩ 89.3% 92.4% (0.015%/cycle)
0.5% CB + 1.0% CNT 33.7 mΩ 8.9 mΩ 93.5% 95.8% (0.008%/cycle)
1.5% CNT 32.0 mΩ 9.3 mΩ 91.8% 90.1% (0.020%/cycle)
0.5% CB + 1.0% graphene 28.2 mΩ 10.1 mΩ 87.6% not reported

If you ranked these four by ohmic resistance alone, you would pick the graphene blend. It has the lowest ohmic impedance of the group — and the worst rate performance, and the highest charge-transfer impedance.

The blend that wins on both rate and cycling is not the lowest-resistance one. It is the CB+CNT blend at 33.7 mΩ.

The mechanism: graphene maximizes the electron path by wrapping particles in a 2D face contact, but the same sheet raises pore tortuosity and lengthens the ion path. Electron conduction and ion transport are not co-directional. That is why the charge-transfer term moves the wrong way (10.1 mΩ) while the ohmic term improves.

Pure CNT has the mirror-image problem. At 500 cycles it retained 90.1% — worse than the plain carbon-black blend — with the highest decay rate of the four (0.020%/cycle). The source attributes this to missing short-range nodes: the long-range skeleton is there, but local particle-surface contact is left with blind spots.

What this means for pilot-line teams

Never sign off a conductive-additive formulation on a four-probe resistivity number. Split ohmic and charge-transfer impedance with EIS, then rank on rate and cycle. “Lower resistance wins” is the trap this dataset was built to expose.


Graphene’s steric penalty needs two conditions at once

Graphene steric penalty needs two conditions at once Qualitative condition matrix from the source article. No numeric values were reported. FIG 4 Flake size vs particle size Flake <= particle Flake >> particle Thin electrode (13 / 26 um) Thick electrode (39 / 52 um) No complete wrapping Ion channels stay open; resistivity dominates. Steric effect masked Short ion path; 1% to 10% graphene kept improving rate. Partial coverage Some tortuosity; validate at product areal loading. Steric penalty appears 5% graphene performed worse than 3.5%; polarization above 3C. NFPP sits in the worst quadrant: sub-micron particles vs commercial graphene flakes of 3-6 um. Qualitative synthesis from the source article. Thin/thick thresholds (13, 26, 39, 52 um) are as reported; no performance values were given, so no chart curves are drawn.

Fig 3. Qualitative condition matrix. The source reports thickness thresholds (13, 26, 39, 52 µm) but no performance values for these cells, so no numeric curves are drawn.

A graphene sheet is a barrier to ion penetration. Once it spreads through an electrode, it lengthens the ion path and increases pore tortuosity, which shows up as polarization at high current. In one published 10 Ah pouch comparison, a cell with just 1% graphene + 1% carbon black had lower internal resistance and higher energy density than a conventional 7% CB + 3% graphite system — but showed significant polarization above 3C.

Whether that penalty appears depends on two independent variables:

NFPP sits on the wrong side of the second condition, and amplifies the penalty three ways: Na⁺ is larger than Li⁺ (102 pm vs 76 pm); sodium electrolytes are typically 20–30% more viscous at 25°C; and NFPP is commonly made as nano/sub-micron crystals or hollow microspheres, far smaller than commercial graphene flakes of 3–6 µm.

And yet the NFPP literature contains many graphene successes. They are not contradictions — they are all materials-engineering workarounds:

Published NFPP approach Reported result
3D porous graphene-decorated NFPP 118 mAh/g at 0.2C; 53 mAh/g at 100C
Mesoporous NFPP + carbon layer + graphene nanosheets 86.7% retention after 30,000 cycles at 20C
Spray-dried NFPP@rGO microspheres 128 mAh/g at 0.1C; 62.3% after 6,000 cycles at 10C
NFPP + in-situ carbon + expanded graphite 80.5 mAh/g at 50C; 89.85% after 11,000 cycles

The common factor is not “graphene was used.” It is that the graphene was porous, three-dimensional or small-flake — the ion channels were deliberately reopened.

What this means

For NFPP, the graphene decision is not use or don’t use. It is whether flake size and pore structure match your particle size. And step 4 of the validation sequence below has to run on your real electrode thickness, because thin coin cells hide this effect completely.


CNT-only electrodes spring back 6.72% after calendering

CNT-only electrodes spring back 6.72% after calendering Thickness rebound after drying, same 1.5 wt% total loading (LFP data). FIG 3 0 2 4 6 8 Rebound (%) 3.12% 1.5% CB 4.85% 0.5% CB + 1.0% CNT 6.72% 1.5% CNT 2.98% 0.5% CB + 1.0% Gr Context from the source article: Raising compaction 2.1 to 2.3 g/cm3 buys only 4-6% volumetric energy density. Source: published LFP electrode measurements, secondary re-plot. NOT NFPP measurements. The 4-6% figure is the source author’s estimate, not a measured value in these datasets.

Fig 4. Thickness rebound after drying. Source: published LFP measurements, re-plotted. Not NFPP measurements. The 4–6% energy-density note is the source author’s estimate, not a measured value in these datasets.

Rebound is where an electronically optimal formulation quietly loses its gain:

One-dimensional CNT fibers recover elastically, so pure-CNT electrodes rebound at roughly twice the rate of the CB-only blend. The source estimates that raising NFPP compaction from 2.1 to 2.3 g/cm³ buys only about 4–6% in volumetric energy density. A 6.72% rebound gives a large part of that back — which is one reason pure-CNT formulations rarely survive a production line.

Three more process constraints shrink the formulation freedom further:

  1. Oil absorption. Graphene exceeds 2000 mL/100g, CNT is 200–440, CB is ~290. NFPP powder itself has a BET surface of 12.5–17.3 m²/g and absorbs NMP significantly. High oil absorption plus high-surface-area active material caps slurry solids content and raises drying energy and cracking risk.
  2. Moisture. Surface Na⁺ sites form an inert Na₂CO₃ layer when they absorb water. The source’s engineering envelope: dew point ≤ -40°C, ≤2000 ppm before calendering, ≤200 ppm after drying; above 1500 ppm with a heating rate above 10°C/min, microcrack rates jump.
  3. Impurities and dispersion. Catalyst-grown multi-wall CNT carries metal residues that suppliers typically spec at ≤100 ppm. CNT needs pre-dispersion with high shear or bead milling; graphene wets easily but restacks, which cancels its surface-area advantage and lowers electrode porosity.

What this means

These four constraints — oil absorption, rebound, moisture, dispersion — are exactly where laboratory results stop transferring to a line. A formulation team that only optimizes impedance will meet all of them at once, late, during scale-up.


What this means for pilot-line teams

Single additives cannot satisfy all three constraints at once, so the practical answer is a point–line–plane network: carbon black fills short-range nodes, CNT builds the long-range skeleton, and small-flake or porous graphene adds face contact where rate capability justifies it.

A defensible starting point from the source review:

Application Starting formulation Watch first Main risk
Long-cycle storage CNT 0.3–0.7% + CB 0.5–1.2%, total ≤2% Resistivity + calender rebound Over-dosing dilutes active material
Power / fast charge CNT 0.5–1.0% + small-flake or porous graphene ≤0.3% Flake-to-particle ratio Steric polarization on thick electrodes
Low / wide temperature CNT-led, avoid high-oil-absorption components Slurry solids + porosity Higher electrolyte viscosity
High-loading thick electrodes CNT-led; graphene must be made porous first Thickness + tortuosity Rate inflection arrives early

The ≤2% total carbon line is the hard boundary: beyond it, the active-material loss costs NFPP more than it would cost LFP.

Validate in this order, or the conclusion will not survive scale-up Five-step sequence recommended in the source article for conductive-additive selection. FIG 5 1 Resistivity curve Find this batch’s real percolation threshold 2 Calender rebound Drop blends with high springback 3 EIS split Separate ohmic from charge-transfer R 4 Rate sweep Locate the polarization inflection point 5 Cycle test Only now run long-term validation Step 4 must run at the product’s real electrode thickness and areal loading. Thin coin cells mask the steric effect, so a formulation that passes the lab can fail on the pilot line. Sequence and wording adapted from the source article. No performance values are implied by this diagram.

Fig 5. Validation order from the source review. No performance values are implied by this diagram.

Validate in this order:

  1. Measure resistivity vs loading to find this batch’s real percolation threshold.
  2. Measure post-calendering rebound and achievable compaction; drop high-rebound candidates.
  3. Use EIS to separate ohmic from charge-transfer impedance — this is where the “lowest R wins” trap gets caught.
  4. Run a rate sweep to locate the polarization inflection point. This must be done at the product’s real thickness and areal loading.
  5. Only then run long-term cycling.

At SZOTECH we build sodium-ion pilot lines, electrode preparation and production lines and cell test equipment precisely for steps 2–5 — where dispersion, calendering and thickness conditions are controlled instead of assumed. If your NFPP formulation looks great in a coin cell and disappoints at pilot scale, the gap is usually here, not in the chemistry.


Limitations

We want to be explicit about what this analysis cannot tell you.


Final thoughts

Three rules are worth keeping from this exercise:

The “lowest resistance wins” heuristic is not wrong because resistance is unimportant. It is wrong because it measures one of two paths. In a carbon-budget-constrained cathode like NFPP, optimizing the electron path in isolation reliably makes the ion path worse — and the failure only shows up at 5C, on a thick electrode, at production loading.

If you are scaling an NFPP formulation, start with the five-step validation order above and treat step 4 as non-negotiable.


About SZOTECH: Sanzhou Operon Power Technology Co., Ltd provides battery R&D equipment, pilot lines, cell manufacturing equipment and turnkey production lines for lithium-ion, sodium-ion and emerging battery chemistries.

Related materials and equipment

For product and process context, see SZOTECH’s LiFePO₄ cathode powder, Super P conductive carbon black and high-structure carbon black. These catalogue pages are separate from the published measurements analyzed above.

For electrode process equipment, explore electrode manufacturing equipment.